Euchner AS-i 3.0 Command Interface Manuel d'utilisateur télécharger pdf (Page 4)

AS-i 3.0 Command Interface Table of Contents

Subject to reasonable modifications due to technical advances Id.-No.: 102875 Issue date - 03.12.07 EUCHNER GmbH + Co. KG

Kohlhammerstraße 16, D-70771 Leinfelden-Echterdingen Tel. +49/711/7597-0, Fax +49/711/753316

4.4 AS-i Diagnosis ....................................................................................................31

4.4.1 Overview of the commands ...............................................................................31

4.4.2 Get Lists and Flags (Get_LPS, Get_LAS, Get_LDS, Get_Flags)

(GET_LISTS) .....................................................................................................31

4.4.3 Get Flags (GET_FLAGS) ...................................................................................33

4.4.4 Get Delta List (GET_DELTA) .............................................................................34

4.4.5 Get list of corrupted Slaves (GET_LCS and GET_LCS_R6 (6CH)) ..................35

4.4.6 Get list of activated Slaves (GET_LAS) .............................................................35

4.4.7 Get list of detected AS-i Slaves (GET_LDS) ......................................................36

4.4.8 Get list of peripheral faults (GET_LPF) ..............................................................37

4.4.9 Get list of offline Slaves (GET_LOS) .................................................................37

4.4.10 Set list of offline Slaves (SET_LOS and SET_LOS_R6 (6Dh)) .........................38

4.4.11 Get transm.err.counters (GET_TECA) ...............................................................39

4.4.12 Get transm.err.counters (GET_TECB) ...............................................................40

4.4.13 Get transm.err.counters (GET_TEC_X) .............................................................41

4.4.14 Read fault detector (READ_FAULT_DETECTOR) ............................................41

4.4.15 Read list of duplicate addresses (READ_DUPLICATE_ADDR) ........................42

4.5 Configuration of AS-i Master .............................................................................43

4.5.1 Overview of the commands ...............................................................................43

4.5.2 Set operation mode (SET_OP_MODE: Set_Operation_Mode) .........................43

4.5.3 Store actual configuration (STORE_CDI) ..........................................................44

4.5.4 Read actual configuration (READ_CDI) .............................................................45

4.5.5 Set permanent configuration (SET_PCD) ..........................................................45

4.5.6 Get extended permanent configuration (GET_PCD) .........................................46

4.5.7 Set list of projected slaves (SET_LPS and SET_LPS_R6 (6Bh)) ......................47

4.5.8 Get list of projected slaves (GET_LPS) .............................................................48

4.5.9 Store actual parameters (STORE_PI) ...............................................................48

4.5.10 Write parameter (WRITE_P) ..............................................................................49

4.5.11 Read parameter (READ_PI: Read_Parameter) .................................................49

4.5.12 Set permanent parameter (SET_PP) .................................................................50

4.5.13 Get permanent parameter (GET_PP) ................................................................50

4.5.14 Set auto address enable (SET_AAE) ................................................................51

4.5.15 Change slave address (SLAVE_ADDR) ............................................................51

4.5.16 Write AS-i slave extended ID1 (WRITE_XID1) ..................................................52

4.6 Other commands ................................................................................................53

4.6.1 Overview of the commands ...............................................................................53

4.6.2 IDLE ...................................................................................................................53

4.6.3 Read input data image (READ_IDI) ...................................................................54

4.6.4 Write output data image (WRITE_ODI) .............................................................54

4.6.5 Read output data image (READ_ODI) ...............................................................55

4.6.6 Set offline mode (SET_OFFLINE) .....................................................................55

4.6.7 Release data exchange (SET_DATA_EX) ........................................................56

4.6.8 Rewrite DPRAM (REWRITE_DPRAM) ..............................................................56

4.6.9 BUTTONS ..........................................................................................................57

4.6.10 FP_PARAM ........................................................................................................57

4.6.11 FP_DATA ...........................................................................................................58

4.6.12 EXT_DIAG .........................................................................................................58

4.6.13 RD_EXT_DIAG ..................................................................................................59

4.6.14 Inverter ...............................................................................................................60

1 2 3 4 5 6 7 8 9 ... 97 98

Commentaires sur ces manuels

Pas de commentaire

Euchner AS-i 3.0 Command Interface Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Sécurité Euchner AS-i 3.0 Command Interface